YPIL, Cable Accessories, Heat Shrink, Heat Shrinkable, Cold Shrinkables Cable Termination, Non tracking Tubing
YPIL, Heat Shrinkable, Telecom Cable Joints Power Cable Jointing Kits Cable Jointing Accessories Electrical Projects Enquiry for Cable Joints,Terminations,Accessories Opportunities for Entrepreneurship Contact for Cable Jointing Systems Newsletter Sitemap Yamunapower  
    PRODUCTS >> Joints | Terminators | Accessories | FRP / Composite | VCB | Composite Polymer Insulators | Elbow Connectors | SCIT  
 
  Joints
  Terminations
    Heat Shrinkeble
    Cold Shrink
    Resin Cast
    Push on Type
  Accessories
  FRP / Composite
  VCB
  Composite Polymer Insulators
  Elbow Connectors
  SCIT

Terminations
Pre-Moulded Cable Termination for XLPE/EPR Cable Up to 33 kV Tested & Conforming to VDE-0278/IS:13573 & Other National / International Standards

YPIL Push-on type terminations have been indigenously designed to suit the environmental requirements of hot, arid, humid & tropical countries, wherein extremes of temperature, humidity, salinity etc. are encountered continuously.Unlike the other apparently similar systems available, which are basically designed for use in cold European Climates. YPIL Push-on termination have been fundamentally engineered to perform in the invasive & corrosive climates prevalent in the tropical & shore-lined regions, without mitigating the system capabilities to perform in cold environment.

RELIABILITY An extensive performance test study carried our as per various National/International quality standards including VDE-0278, IS:13573:92 (Latest) & IEEE 48 followed by several years of performance ensures the high quality & reliability of YPIL Push-On Terminations.		 Pre-Moulded Cable Terminations, Push on Type Termination   Push on Type Termination

STRESS CONTROL
This is done, a YPIL Push-on system, by a stress cone made of highly insulating & non-tracking material bonded to a semi-conducting & concentric section. The design of the stress cone has been optimized to ensure, even distribution of stresses at the portion where the screen is terminated & adequate dielectric strength of the insulating profile. The stress cone has been designed to operate upto 36 Kv. The S.C. pad used for maintaining the continuity of stress cone with insulation screen of the cables is a special grade of elastomer with cold flow properties which results in for a homogeneous mass free from air pockets & micro voids between the screen & insulated profile of stress cone which insures for an absolute discharge free termination.

SHELF LIFE
 The factory moulded components for making YPIL Push-on terminations have infinite shelf life under normal conditions.

FLAME RETARDANCY
 YPIL push-on terminations are made with materials made out of special formulations to offer substantial degree of flame retardancy.

APPLICATION
 Outdoor / Indoor switchgear, motor, transformer, switchyards etc.
DENSONS RESIN CAST SYSTEM KITS
FOR 33 KV H/HSL TYPE PILC CABLE



Ordering Information
Dia. over prepared XLPE insulation (mm2) 6.6KV (UE)/11KV(E) Cabel Size (mm2) Kit Code 11KV (UE)/22KV(E) Cabel Size (mm2) Kit Code 33 KV(E) Cable Size (mm2) Kit Code
13.7-15.9 25-35 DPE-1 Enquiry - - - -
15.8-18.8 50-70 DPE-2 Enquiry - - - -
18.1-21.5 95 DPE-3 Enquiry 35-50 DPE-21 Enquiry - -
20.7-24.6 120-150 DPE-4 Enquiry 70 DPE-22 Enquiry - -
23.9-28.5 185-240 DPE-5 Enquiry 95-120-150 DPE-23 Enquiry 50 DPE-31 Enquiry
28.4-33.8 300-400 DPE-6 Enquiry 185-240 DPE-24 Enquiry 70-120 DPE-32 Enquiry
33-36.6 500 DPE-7 Enquiry 300 DPE-25 Enquiry 150-185 DPE-33 Enquiry
35.7-39.7 - - 400 DPE-26 Enquiry 240-300 DPE-34 Enquiry
39.3-43.1 630 DPE-8 Enquiry 500 DPE-27 Enquiry - -
42.5-48.1 800 DPE-9 Enquiry 630 DPE-28 Enquiry 400-500 DPE-35 Enquiry
48-54 1000 DPE-10 Enquiry 800-1000 DPE-29 Enquiry 630 DPE-36 Enquiry
TOP
 
DENSONS RESIN CAST SYSTEM KITS
FOR 22 KV H/HSL TYPE PILC CABLE

Ordering Information
Dia. over prepared XLPE insulation (mm2) 6.6KV (UE)/11KV(E) Cabel Size (mm2) Kit Code 11KV (UE)/22KV(E) Cabel Size (mm2) Kit Code 33 KV(E) Cable Size (mm2) Kit Code
13.7-15.9 25-35 DPO-1 Enquiry - - - -
15.8-18.8 50-70 DPO-2 Enquiry - - - -
18.1-21.5 95 DPO-3 Enquiry 35-50 DPO-21 Enquiry - -
20.7-24.6 120-150 DPO-4 Enquiry 70 DPO-22 Enquiry - -
23.9-28.5 185-240 DPO-5 Enquiry 95-120-150 DPO-23 Enquiry 50 DP0-31 Enquiry
28.4-33.8 300-400 DPO-6 Enquiry 185-240 DPO-24 Enquiry 70-120 DPO-32 Enquiry
33-36.6 500 DPO-7 Enquiry 300 DPO-25 Enquiry 150-185 DPO-33 Enquiry
35.7-39.7 - - 400 DPO-26 Enquiry 240-300 DPO-34 Enquiry
39.3-43.1 630 DPO-8 Enquiry 500 DPO-27 Enquiry - -
42.5-48.1 800 DPO-9 Enquiry 630 DPO-28 Enquiry 400-500 DPO-35 Enquiry
48-54 1000   DPO- 10 Enquiry 800-1000 DPO-29 Enquiry 630 DPO-36 Enquiry
TOP
 
DENSONS RESIN CAST SYSTEM KITS
FOR 11 KV PILC CABLE

Ordering Information
Typical Test Performance      
TEST 11 kV 22 kV

33 kV
AC Dry Withstand (One minute) 35 KV 55 KV 75 KV
Impulse Withstand Voltage (KV) 10+VE & 10-VE 75 125 170
Partial Discharge Test at 2Uo < 20 Pc < 20 Pc < 20 Pc
 
TOP | NEXT
Copyright © 2006-2007. All rights reserved. Yamuna Power & Infrastructure Ltd.
RSS Feed Sitemap
Resources Disclaimer | Designed by : India Internets